One Owner: 1973 Chevrolet Blazer K5 4×4 Cheyenne
Where are we in the Blazer-mania cycle? Are prices moderating or it is still just nuts out there? Well, the highwater mark was this ’71 restomod that brought a cool $440k at Mecum in January of 2022. There’s this dealer, who wants $230k for a ’73; his listing is at least two months old. A scattering of “high bids” here represent trucks that didn’t sell at reserve or better very recently. Mecum’s upcoming Kansas City auction has eight Blazers of various flavors on offer, Hemmings reliably lists tens at a time (84 right now). With that kind of supply available, if even a few potential buyers start balking, prices will weaken. Here on eBay is a bellwether Blazer, this 1973 4×4 Cheyenne. Bidding has reached $16,200 and thankfully, that exceeds whatever reserve was in play. We can quarrel with the level in light of buying dirt cheap Blazers twenty years ago, but it’s reasonable today despite the chellenges of this example which we’ll see in a minute. The truck was purchased by the mayor of Hardin, Montana from a dealer in Wyoming; the mayor was its only owner. It has been listed by a dealer located in Greenacres, Washington.
The 350 cu. in. V8 runs strong, generating about 165 hp but sucking up about 10 mpg; the odo reads only 69,567 which may or may not be the total mileage traveled. The transmission is a three-speed automatic mated with a dual-range transfer case. This was the first year of the second generation Blazer – what GM called the “Rounded Line” but is colloquially known as the square-body. Length grew by 7″ over the first-gen Blazer, which was not helpful for performance or mileage. This truck has a 4″ lift kit installed.
The interior is tatty here and there – the door pocket elastic has given way, the steering wheel is faded, the center console has a crack. But the bucket seats have been reupholstered and the carpet is new. The dealer installed a new dash pad. The wood grain applique on the dash, door, and rear trim panels is original – part of the top-shelf Cheyenne trim package. A removable top was supplied with ’73-’75 Blazers – a big advantage in my opinion. Of course, they’re hard to remove and replace, but it’s great to know you can! The chrome shines well though the paint shows its age here and there.
Yes, at this price there has to be bad news. and here we have it – rusty skirts! The damage isn’t confined to one side, of course. The floors look okay, but only close inspection will confirm that. I would feel compelled to fix the sheet metal, but then, where are we with paint? I’m seeing dollar signs here…. How would you improve this Blazer, or would you just drive it as is?
Auctions Ending Soon
2006 Ford Mustang Saleen S281 SCBid Now3 hours$16,000
2002 Subaru Impreza WRXBid Now3 days$333
1975 Chevrolet Corvette ConvertibleBid Now3 days$3,000
1964 Ford F-100 Camper CustomBid Now3 days$2,000
2006 Jeep Wrangler SportBid Now5 days$10,500
Comments
Really nice. The ’73-’75 K5 Blazers are my favourite square-body models as the entire fiberglass roof is removable. From ’76 on, only the rear “cap” section of the roof was removable. I have owned a ’75 for almost 20 years, and remove the roof every spring.
I am always watching for project K5s locally, and most are rotten. The nicer ones have been overpriced, and often too modified for my taste.
The truck here looks to be a very viable project. If it were mine, I would replace the short exhaust with a proper, full stainless dual system, lose the lift kit, do paint/body , replace the outside mirrors with OE style, and fit OE style argent rally wheels with trim-rings and caps.
If this truck was local, I would likely bid.
Good thoughts. I would do most of what you said except for the rally wheels. I hate them. It would be only an occasional driver at 10 MPG though. Glad to see it’s mostly original.
I think 8 mpg is closer to what I got but I had the smaller V 8.
What’s up with the fuse by the air conditioner?
I would love to have this in my driveway ! ……❤️
I agree as well, except I would try to source the actual original style hubcaps either in Chrome or white and stock steel rims or perhaps slightly wider than stock but not too much. These hub caps Im pretty sure are from a newer one. Late 70s early 80s.
Had a 77 for years. It is in about the same shape as this unit, only mine is a stick. Given the car world right now. I am glad I kept it. Rust is the only enemy.
Rusted butterscotch
It would be a nice resto project, but he’s California Dreaming if he thinks anyone is stupid enough to lay out nearly 17k for it. Trying to find a body shop nowadays that does rust work is nearly impossible, and if you do, or if you find someone that does fabrication/ body work, it’s gonna cost you a lot of cabbage. GLWTS……